2014 - 2020 Chevy Impala 2.5L Torque Specs

2014 Chevy Impala Rear End Torque Specs

Click the area you are looking for!


Chevy Impala 2.5L Repair Information

Chevy Impala 2.5L Rear End Repair Information

Here you can find information regarding repairs to the Chevy Impala rear end system. These repairs include the rear control arms installation, the rear swaybar information and bolt torque specs, the rear diff fluid change procedures, and the rear end watts system installation. All of these repairs and procedures include in depth details on how to perform the replacement and or repair. They also contain all the detailed torque specs needed for each bolt involved in the repair.

Rear Wheel Hub Torque Specs

Chevy Impala Rear Wheel Hub
The Impala rear wheel hub is held to the vehicle much like the front wheel hubs. There are 4 bolts which torque into nuts that hold the hub onto the rear wheel suspension. To remove these bolts and the hub assembly you will first need to jack up the vehicle and remove the braking system from the corresponding side of the vehicle. Once out of the way you can remove the bolts by using the access holes on the hub plate itself. Be sure to hold the nuts on the other end with a wrench. Once all 4 have been removed you can then remove the rear hub assembly and place a new part into its place. The 4 bolts can be torqued down to 47 ft-lbs.

Chevy Impala Rear Wheel Hub Torque Specs : 47 ft-lbs

 

Rear Control Arms Installation

Chevy Impala Rear Control Arms
The rear suspension of the Chevy Impala consists of a solid axle that is held to the vehicle through the use of rear control arms and a spring suspension. The control arms of this rear suspension make up a critical part of the suspensions functionality and without them the rear end would detach from the vehicle. This is why it is important to tighten down the bolt specs to manufacturers specifications. The rear control arms range from the vehicles frame to the rear axle. On each side there is a bolt and a nut that needs to be installed. During installing make sure to tighten the bolt side down to 80 ft-lbs and the nut side to 60 ft-lbs. This can be done on both the axle and frame side of the control arm. There is also a track bar and a torque arm that runs from one side of the axle to the other. The track bar will need to be tightened down to 61 ft-lbs and the torque bar can be tightened down to 96 ft-lbs.

Chevy Impala Rear Control Arm Nut Side Torque Spec : 60 ft-lbs

Chevy Impala Rear Control Arm Bolt Side Torque Spec : 80 ft-lbs

Chevy Impala Rear Track Bar Torque Spec : 61 ft-lbs

Chevy Impala Rear Torque Bar Torque Spec : 96 ft-lbs

 

Rear Shocks Installation

Chevy Impala Rear shock
To replace the rear shocks on a Chevy Impala you will need to remove two sets of bolts/nuts located at the bottom and top of the shock. Both of these fasteners can be accessed from underneath the vehicle by jacking it up and removing the wheel. Once you have removed the 2 upper nuts and the single lower bolt the old shock can be removed from the vehicle. From here we can install the new shock in place of the old one and tighten up the upper nuts to 18 ft-lbs. The lower bolt can then be installed and torqued down to 133 ft-lbs. Once both set of fasteners have been installed you have finished installing the new rear shock and can reinstall the wheel and go for a test drive.

Chevy Impala Rear Shock Upper Nuts Torque Specs : 18 ft-lbs

Chevy Impala Rear Shock Lower Bolt Torque Specs : 133 ft-lbs

 

Rear Stabilizer Bar Installation

Chevy Impala Rear Stabilizer Bar
To replace the rear stabilizer bar on the Chevy Impala you must first remove the old part from the vehicle. The stabilizer bar consists of a large bar that goes from one side of the vehicle to the other. There is one endlink on each side of the bar which can be removed and replaced. The bar contains 2 brackets which hold it up to the vehicles frame. When installing new parts be sure to torque down the stabilizer bar brackets to 50 ft-lbs. The endlinks can be torqued down to 55 ft-lbs.

Chevy Impala Rear Stabilizer Bar Endlinks Torque Specs : 55 ft-lbs

Chevy Impala Rear Stabilizer Frame Brackets Torque Specs : 50 ft-lbs

 


Rear Control Arms Torque Specs
Rear Control Arm Bolt Side Torque Spec 80 ft-lbs
Rear Control Arm Nut Side Torque Spec 60 ft-lbs
Rear Track Bar Torque Spec 61 ft-lbs
Rear Torque Bar Torque Spec 96 ft-lbs
Rear Suspension Torque Specs
Rear Wheel Hub Bolts Torque Spec 47 ft-lbs
Rear Shock Torque Specs
Rear Shock Upper Nuts Torque Spec 18 ft-lbs
Rear Shock Lower Bolt Torque Spec 133 ft-lbs
Rear Shock Torque Specs
Rear Stabilizer Bracket Torque Spec 50 ft-lbs
Rear Stabilizer Endlinks Torque Spec 55 ft-lbs